WaGuns.org
https://waguns.org/

XD / XDm How to Vids
https://waguns.org/viewtopic.php?f=48&t=24
Page 1 of 2

Author:  Massivedesign [ Tue Mar 15, 2011 10:24 am ]
Post subject:  XD / XDm How to Vids

Here are some great XD & XDm videos that show you how to work on and modify your XD/XDm.
If you have any videos, please post them up in this thread. Make sure to give credit to any specific author too.

Please note that these videos are not an endorsement for any company and attempting the content in any of these videos should be taken at your own risk. Warranties may be voided.

Springfield Armory XDM introduction video to detail stripping and servicing by Springer Precision

Instructions on how to detail strip of your Springfield Armory XD and XDM slides

Springfield XDM and XD frame detail assembly instructions by Springer Precision Part 1 of 3
Springfield XDM and XD frame detail assembly instructions by Springer Precision Part 2 of 3
Springfield XDM and XD frame detail assembly instructions by Springer Precision Part 3 of 3

XD/XDM magazine release installation by Springer Precision Magazine release

Springfield XDM and XD grip safety detail assembly instructions

All the above videos are created by Springer Precision

Author:  Just in joy [ Mon Apr 18, 2011 4:49 pm ]
Post subject:  Re: XD / XDm How to Vids

here is also a link for XD parts I stumbled across.

http://www.pistolgear.com/products.php?id=41

Author:  Just in joy [ Fri Apr 22, 2011 8:39 pm ]
Post subject:  Re: XD / XDm How to Vids

http://nwtownsends.smugmug.com/photos/238574776-XL.jpg

Above is a link for a break down on the XD models which is the same as the photo below.

Image

Author:  Massivedesign [ Fri Apr 22, 2011 8:50 pm ]
Post subject:  Re: XD / XDm How to Vids

nice

Author:  Just in joy [ Fri Apr 22, 2011 9:45 pm ]
Post subject:  Re: XD / XDm How to Vids

I am on the hunt for the XD and XDM info for the site.

Author:  olydemon [ Thu Mar 01, 2012 10:07 am ]
Post subject:  Re: XD / XDm How to Vids

Here is a new XDm Trigger Job video.


Author:  olydemon [ Thu Mar 01, 2012 9:20 pm ]
Post subject:  Re: XD / XDm How to Vids

Cool XD functional rendering videos.




Author:  timmytowbowman [ Tue Feb 12, 2013 6:05 pm ]
Post subject:  Re: XD / XDm How to Vids

Thanks for the info guys. I have not broke mine down yet, but see it will be a bit different than the Glocks I am use to. The videos are going to be very helpful.

Author:  Massivedesign [ Tue Feb 12, 2013 6:10 pm ]
Post subject:  Re: XD / XDm How to Vids

It's easy... Really.

Author:  timmytowbowman [ Tue Feb 12, 2013 6:18 pm ]
Post subject:  Re: XD / XDm How to Vids

I admit I am a bit intimidated, but look forward to breaking it down here in the near future. I hope to find someone in the local area, that is able to install my night sites. I hear some folks have to send them off, and I would rather not have to go through that experience.

Author:  The DUDE Abides [ Tue Feb 12, 2013 8:05 pm ]
Post subject:  Re: XD / XDm How to Vids

I just picked up a XDM 45 4.5 on Saturday, thanks for the thread.

Author:  Massivedesign [ Tue Feb 12, 2013 8:25 pm ]
Post subject:  Re: XD / XDm How to Vids

timmytowbowman wrote:
I admit I am a bit intimidated, but look forward to breaking it down here in the near future. I hope to find someone in the local area, that is able to install my night sites. I hear some folks have to send them off, and I would rather not have to go through that experience.



I'll send you a PM.

Author:  bajarob [ Tue Feb 12, 2013 8:43 pm ]
Post subject:  Re: XD / XDm How to Vids

Great thread. Over the years I guess i've always just started pulling shit apart and figuring it out (piece by piece...remove, replace several times for each piece) as I go along. Lay everything out on a while sheet as it comes apart.
I guess with the internet, I now have a better way :bow:
Thanks

Author:  joao01 [ Tue Feb 17, 2015 1:33 pm ]
Post subject:  Re: XD / XDm How to Vids

lot of good info from James (aka XDMan). I can't link to his youtube channel at the moment, but you should be able to find more of his vids:

http://www.tacti-cool.com/detail-disassembly/

Author:  ANZAC [ Tue Feb 17, 2015 9:34 pm ]
Post subject:  Re: XD / XDm How to Vids

timmytowbowman wrote:
I admit I am a bit intimidated, but look forward to breaking it down here in the near future. I hope to find someone in the local area, that is able to install my night sites. I hear some folks have to send them off, and I would rather not have to go through that experience.


I sent my slide out for the sights, but if you have a sight pusher tool it shouldn't be too hard.

The rest of pretty much anything on the XD/XDm is a piece of cake.

Note the loaded chamber indicator can get really gummed up. Every second cleaning I pop the roll pin out and clean it really well.

Page 1 of 2 All times are UTC - 8 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/