|
|
|
It is currently Thu May 02, 2024 12:42 pm
|
|
Page 1 of 1
|
[ 15 posts ] |
|
Mixed brass, case capacity and QuickLoad
Author |
Message |
MadPick
Site Admin
Location: Renton, WA Joined: Sun Mar 13, 2011 Posts: 52110
Real Name: Steve
|
I've been doing a lot of .223 loading the last few days, putting together another batch of prairie dog rounds. I'm using mixed brass, 26.0 grains of Hodgdon Benchmark, 50-grain Hornady Z-Max bullets, Wolf small rifle primers and an OAL of 2.24". As I load, most of the rounds look roughly like the one on the right in the photo below, where you need to look down into the case a bit to see the powder because it comes to roughly the bottom of the neck: However, occasionally I'll see one like this, with the powder almost to the top of the case: (And yes, that is still the correct powder charge -- I verified it.) Every single one of the cases that had the powder level that high had S&B head stamps. So, I checked the water capacity of one of them and it was 29.6 grains. I checked a couple of Lake City cases for comparison, and they held 30.2 grains of water. So . . . what does that mean? Well, per QuickLoad it means quite a lot. And yes, I'm aware that this is a pretty hot load to begin with. For reference, the maximum spec chamber pressure for .223 Remington is: Per SAAMI: 55,000 psi Per CIP (European): 62,000 psi So, if I input all of my numbers with the Lake City brass into Quickload, it tells me that my chamber pressure is 59,082 psi and my predicted muzzle velocity with a 24" barrel is 3421 fps: And if I lower the case capacity to the S&B number, the chamber pressure jumps to 62,179 psi -- above even the European max! Predicted muzzle velocity with a 24" barrel is 3455 fps. And yes, I've measured muzzle velocity in the 3440 fps range from my 24" AR-15 with this load, so the predicted velocities above are right on. My conclusions? - Case capacity matters, especially if you already have a hot load. - I've shot a lot of this particular load in the past, including from S&B brass, so I'm going to shoot everything that I loaded. - I'm going to sort out the S&B and I won't use for this load anymore; I'll save it for lighter plinking loads. Any thoughts?
_________________SteveBenefactor Life Member, National Rifle AssociationLife Member, Second Amendment FoundationPatriot & Life Member, Gun Owners of AmericaLife Member, Citizens Committee for the Right to Keep and Bear ArmsLegal Action Supporter, Firearms Policy CoalitionMember, NAGR/NFGRPlease support the organizations that support all of us.Leave it cleaner than you found it.
|
Mon May 29, 2017 1:41 pm |
|
|
SAGELA
Site Supporter
Location: Kirkland Joined: Mon Mar 28, 2011 Posts: 239
|
CPI/NATO spec of 62,000 PSI data are available on Western Powders website. If I were loading to NATO spec I'd want a NATO leade in my rifle's barrel. And I'd be looking at case capacity (as you suggest) to prevent fudging the spec. Particularly when you only get 34'/s in doing it.
|
Mon May 29, 2017 5:03 pm |
|
|
MadPick
Site Admin
Location: Renton, WA Joined: Sun Mar 13, 2011 Posts: 52110
Real Name: Steve
|
SAGELA wrote: If I were loading to NATO spec I'd want a NATO leade in my rifle's barrel. Does that mean, "I'd want a rifle chambered in 5.56, not .223"?
_________________SteveBenefactor Life Member, National Rifle AssociationLife Member, Second Amendment FoundationPatriot & Life Member, Gun Owners of AmericaLife Member, Citizens Committee for the Right to Keep and Bear ArmsLegal Action Supporter, Firearms Policy CoalitionMember, NAGR/NFGRPlease support the organizations that support all of us.Leave it cleaner than you found it.
|
Mon May 29, 2017 5:22 pm |
|
|
SAGELA
Site Supporter
Location: Kirkland Joined: Mon Mar 28, 2011 Posts: 239
|
MadPick wrote: SAGELA wrote: If I were loading to NATO spec I'd want a NATO leade in my rifle's barrel. Does that mean, "I'd want a rifle chambered in 5.56, not .223"? These days it usually means a Wylde chamber - most of those are marked ".223 Remington/5.56 NATO" Instead of just extra freebore, it ramps up from freebore to lands/grooves a tad more gradually.
|
Mon May 29, 2017 9:17 pm |
|
|
SixPointEight
Location: Frederickson, WA Joined: Mon Dec 19, 2016 Posts: 194
|
SAGELA wrote: CPI/NATO spec of 62,000 PSI data are available on Western Powders website. If I were loading to NATO spec I'd want a NATO leade in my rifle's barrel. And I'd be looking at case capacity (as you suggest) to prevent fudging the spec. Particularly when you only get 34'/s in doing it. Agreed. 62k PSI is acceptable for 5.56 loads, though I don't often like to push the envelope with mixed brass of unknown loadings. Interesting how thick that S&B case head must be. Surely it can handle the extra pressure Sent from my SAMSUNG-SM-G920A using Tapatalk
|
Sun Jun 04, 2017 9:10 pm |
|
|
Sinus211
Site Moderator
Location: Marysville Joined: Thu Mar 22, 2012 Posts: 13514
Real Name: Mike
|
That Benchmark powder is semi extruded. I know you've verified the case volume difference but I would think it's also possible that the stick powder in some of those cases settled better than others and some are just sitting a little high. Did you try covering the case mouth and flicking the case to see if the powder settle down lower when agitated?
_________________Licensed/Bonded/Insured Hardwood Floor Installer/Finisher http://www.hardwoodfloorsnw.com/
|
Sun Jun 04, 2017 10:02 pm |
|
|
MadPick
Site Admin
Location: Renton, WA Joined: Sun Mar 13, 2011 Posts: 52110
Real Name: Steve
|
Yeah, it will settle a bit ... but the comparison you see above is real, as neither case has been shaken and the S&B cases consistently looked like that.
The issue isn't that the S&B cases are "too full," just that they are more full than the other cases.
_________________SteveBenefactor Life Member, National Rifle AssociationLife Member, Second Amendment FoundationPatriot & Life Member, Gun Owners of AmericaLife Member, Citizens Committee for the Right to Keep and Bear ArmsLegal Action Supporter, Firearms Policy CoalitionMember, NAGR/NFGRPlease support the organizations that support all of us.Leave it cleaner than you found it.
|
Mon Jun 05, 2017 5:34 am |
|
|
VantageReloading
Site Supporter
Location: Bigfork, MT (Formerly Sammamish, WA) Joined: Sun Feb 15, 2015 Posts: 97
Real Name: Michael Hallak
|
How many SB cases do you have available? Load a set (10 minimum) of those along with another set of your other cases and head to the range to chronograph for any specific velocity spread. As has been mentioned, the pressure isn't so bothersome (don't leave your ammo can in the sun?) but I would be more concerned with velocity spread and the effect on accuracy. I am also curious to know if the sb cases chronograph true to the QL calibrations.
_________________Visit http://www.vantagereloading.com/ for custom ammunition tuned for your firearm.
|
Mon Jun 05, 2017 7:27 am |
|
|
MadPick
Site Admin
Location: Renton, WA Joined: Sun Mar 13, 2011 Posts: 52110
Real Name: Steve
|
VantageReloading wrote: How many SB cases do you have available? Load a set (10 minimum) of those along with another set of your other cases and head to the range to chronograph for any specific velocity spread. All right, I found ten matching S&B cases and ten Lake City 2008 cases. First I checked the average case capacity of all ten cases of each kind: S&B: 28.7 grains of water LC 2008: 30.25 grains of water Here are the QuickLoad predictions with my standard load of 26.0 grains of Benchmark, a 50-grain Z-max bullet and 2.24" OAL with Wolf magnum primer. First, the LC 2008: And the S&B: Note the pressure prediction: 58,864 PSI for the LC 2008 and 67,576 PSI for the S&B. Again, the SAAMI maximum is 55,000 PSI and the CIP (European) maximum is 62,000 LCP. I went to the range yesterday and tested the velocity of the rounds using my 20" Mossberg MVP. I got data for all ten of the LC 2008 rounds, but the Labradar didn't catch the last two S&B rounds . . . so the data below is based on eight rounds of S&B. LC 2008 velocityQL prediction: 3,288 fps Actual: 3,250 fps, standard deviation 12.7 S&B velocityQL prediction: 3,384 fps Actual: 3,337 fps, standard deviation 14.5 So . . . conclusion? I dunno. QL predicted a 96 fps difference, and I saw an 87 fps difference. So that's pretty close, I think? The actual numbers were off by roughly 40 fps, but in my mind that's pretty close for a computer prediction, considering all of the variables involved. Oh, and here are the cases, with S&B on the left and LC 2008 on the right. QL failed to predict the pierced primer.
_________________SteveBenefactor Life Member, National Rifle AssociationLife Member, Second Amendment FoundationPatriot & Life Member, Gun Owners of AmericaLife Member, Citizens Committee for the Right to Keep and Bear ArmsLegal Action Supporter, Firearms Policy CoalitionMember, NAGR/NFGRPlease support the organizations that support all of us.Leave it cleaner than you found it.
|
Mon Jun 26, 2017 7:52 pm |
|
|
Sinus211
Site Moderator
Location: Marysville Joined: Thu Mar 22, 2012 Posts: 13514
Real Name: Mike
|
Nice craters in some of the s&b primers. That's pretty f'd up that they're using brass with lower case volume on such a high pressure round. That could end up being pretty dangerous for those who load at the top end of saami recommendation.
_________________Licensed/Bonded/Insured Hardwood Floor Installer/Finisher http://www.hardwoodfloorsnw.com/
|
Mon Jun 26, 2017 10:15 pm |
|
|
VantageReloading
Site Supporter
Location: Bigfork, MT (Formerly Sammamish, WA) Joined: Sun Feb 15, 2015 Posts: 97
Real Name: Michael Hallak
|
Fascinating - thanks for sharing the results. In no particular order:
Quick load doesn't perfectly approximate chamber pressure, howevee I can't help but notice the rounds with SB cases that are predicted to be over pressure have Significant primer cratering
SD of mid teens for a wolf primer is solid. Good prep work and loading practices for that kind of result.
You haven't calibrated QL for the temperature you faced if you went to the range on Sunday (95*F?) when QL bases calculations on 70*F by default. You'll need to adjust the powder Ba value to calibrate for your lot number of benchmark.
Your 87fps difference vs 96fps difference on the prediction is half of a standard deviation of either of your loads, which renders that value statistically irrelevant if you aren't bothered by the small sample size (18 rounds total). I would say that's "spot on".
Which load shoots better? Better yet, what is the average POI? Do either measures change at all when you mix a magazine?
Keep it coming! You're just getting started ;)
_________________Visit http://www.vantagereloading.com/ for custom ammunition tuned for your firearm.
|
Mon Jun 26, 2017 10:16 pm |
|
|
MadPick
Site Admin
Location: Renton, WA Joined: Sun Mar 13, 2011 Posts: 52110
Real Name: Steve
|
VantageReloading wrote: You haven't calibrated QL for the temperature you faced if you went to the range on Sunday (95*F?) when QL bases calculations on 70*F by default. You'll need to adjust the powder Ba value to calibrate for your lot number of benchmark.) I don't know how to do that. VantageReloading wrote: Which load shoots better? Better yet, what is the average POI? Do either measures change at all when you mix a magazine?) Yeah, I didn't try to test accuracy . . . mostly because although I know I can shoot a good group, I don't have enough confidence in my shooting to give you something statistically significant with only 10 rounds of each type. VantageReloading wrote: Keep it coming! You're just getting started ;) Well, I have no more unloaded Z-max bullets . . . so that's my easy out.
_________________SteveBenefactor Life Member, National Rifle AssociationLife Member, Second Amendment FoundationPatriot & Life Member, Gun Owners of AmericaLife Member, Citizens Committee for the Right to Keep and Bear ArmsLegal Action Supporter, Firearms Policy CoalitionMember, NAGR/NFGRPlease support the organizations that support all of us.Leave it cleaner than you found it.
|
Mon Jun 26, 2017 10:23 pm |
|
|
TwizDD
Site Supporter
Location: Eatonville Joined: Fri Nov 11, 2011 Posts: 895
Real Name: Tony
|
Fuck all this reloading nonsense! Did no one notice, the Sasha Grey reference!? Well done Steve..well done! Aaaannnndddd... Noooow... back to our regularly scheduled reloading nonsense! Oh by the way...
_________________ "I expect to pass through life but once. If, therefore, there be any kindness I can show, or any good thing I can do for any fellow being, let me do it now ... as I shall not pass this way again." - William Penn
|
Thu Jul 06, 2017 3:28 pm |
|
|
PMB
In Memoriam
Joined: Wed Mar 6, 2013 Posts: 12018
|
TwizDD wrote: Fuck all this reloading nonsense! Did no one notice, the Sasha Grey reference!? Well done Steve..well done! Aaaannnndddd... Noooow... back to our regularly scheduled reloading nonsense! Oh by the way... That is Sasha Grey? At first I thought Steve just went ahead with his transformation. and still
|
Thu Jul 06, 2017 3:38 pm |
|
|
sportsdad60
Site Supporter
Location: The banana belt of MT Joined: Wed Dec 30, 2015 Posts: 8587
Real Name: Brian
|
Nice report out Steve! Damn! It's science! I love it!
_________________ "I hate to advocate drugs, alcohol, violence, or insanity to anyone, but they've always worked for me."- Hunter S. Thompson
|
Tue Jul 11, 2017 7:28 am |
|
|
|
|
Page 1 of 1
|
[ 15 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 9 guests |
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
|
|