|
|
|
It is currently Thu Apr 25, 2024 4:05 am
|
|
Page 1 of 1
|
[ 9 posts ] |
|
Restoring a stock to original condition
Author |
Message |
sportsdad60
Site Supporter
Location: The banana belt of MT Joined: Wed Dec 30, 2015 Posts: 8587
Real Name: Brian
|
Anyone want to share a step by step process, including materials, to restore an old stock back to it's linseed oil condition? I don't want to sand anything, just remove old varnish and re-oil the stock.
Thanks!
_________________ "I hate to advocate drugs, alcohol, violence, or insanity to anyone, but they've always worked for me."- Hunter S. Thompson
|
Thu Oct 19, 2017 8:51 am |
|
|
TINCANBANDIT
Site Supporter
Location: Mohave Valley Arizona Joined: Fri May 20, 2011 Posts: 13371
Real Name: Casey
|
Use acetone to remove oil and oil finish
then sand with 600 grit with the linseed oil as a lubricant. Then wipe the slurry into the grain to fill the grain, do this 3 or 4 times, then apply oil, rubbed in by hand until dry, let cure for 3 days
If the surface is not baby butt smooth, use some rubbing compound and gently polish the surface. Then seal with carnuba wax
_________________Actor portrayal, Action figures sold separately, You must be at least this tall to ride, Individual results may vary, Sales tax not included, All models are over 18 years of age, upon approval of credit, Quantities are limited while supplies last, Some restrictions apply, Not available with other offers, At participating locations only, Void where prohibited, Above terms subject to change without notice, Patent pending.See my blog: http://tincanbandit.blogspot.com/
|
Thu Oct 19, 2017 8:58 am |
|
|
sportsdad60
Site Supporter
Location: The banana belt of MT Joined: Wed Dec 30, 2015 Posts: 8587
Real Name: Brian
|
Thanks, Mind you I have old varnish on the wood someone added some decades ago that wasn't factory.I've heard of some guys using a varnish stripper, then acetone.
_________________ "I hate to advocate drugs, alcohol, violence, or insanity to anyone, but they've always worked for me."- Hunter S. Thompson
|
Thu Oct 19, 2017 9:04 am |
|
|
RENCORP
Site Supporter
Location: East of Japan, not by much. Joined: Fri Jun 3, 2011 Posts: 12990
|
Use a citrus based furniture stripper. Hose it on, and bag the stock for a few hours to let it work in. Wash it off with dish soap and water, rinse thoroughly. Let it dry out thoroughly, then go at it with the oil - first couple of coats, apply really wet with OOOO steel wool to knock down any rough grain, and create a smooth uniform finish. Lay it on wet, let it stand for an hour or so, and wipe it dry. Let the stock dry for a couple days between coats. Lay down about 4-6 coats altogether - the last 2-4 coats can be just oil wet rag applied before standing for an hour, and wiped dry before drying out.
_________________ Give a man a fish, and he will eat for a day. Give a man a fishing pole, and he will drink too much beer, get tangled in fish line, hook himself in the nose casting, fall overboard, and either drown, or, go home hungry and wet. Give a man a case of dynamite, and he will feed the whole town for a year!
BE ON NOTICE: PRIVACY NOTICE: Warning - any person and/or institution and/or Agent and/or Agency of any governmental structure including but not limited to the United States Federal Government also using or monitoring/using this website or any of its associated websites, you do NOT have my permission to utilize any of my profile information nor any of the content contained herein including, but not limited to my photos, and/or the comments made about my photos or any other "picture" art posted on my profile.
You are hereby notified that you are strictly prohibited from disclosing, copying, distributing, disseminating, or taking any other action against me with regard to this profile and the contents herein. The foregoing prohibitions also apply to your employee, agent, student or any personnel under your direction or control.
The contents of this profile are PRIVATE and legally privileged and confidential information, and the violation of my personal privacy is punishable by law. UCC 1-103 1-308 ALL RIGHTS RESERVED WITHOUT PREJUDICE
|
Thu Oct 19, 2017 9:05 am |
|
|
mtnwkr
Site Supporter
Location: Port Orchard Joined: Sun Dec 23, 2012 Posts: 797
Real Name: Josh
|
I did just this a few years ago, the stock was covered in some kind of varnish too. I used a regular old pink eraser wrapped in 400 grit to "sand in" each coat of oil until the last couple when I went to 600, 800, 1200 grit. The eraser will keep you from making low spots, the sandpaper will keep things smooth. I also taped off all the checkering until the last coat.
|
Thu Oct 19, 2017 11:04 am |
|
|
sportsdad60
Site Supporter
Location: The banana belt of MT Joined: Wed Dec 30, 2015 Posts: 8587
Real Name: Brian
|
I really don't want to sand smooth anything, I want to keep the dings and what not in the stock. Each one probably has a story to tell, so maybe I'll just remove the varnish as suggested above, wipe it down with acetone, then begin the "linseed oil" slurry with 000 steel wool or 1200 grit
_________________ "I hate to advocate drugs, alcohol, violence, or insanity to anyone, but they've always worked for me."- Hunter S. Thompson
|
Thu Oct 19, 2017 1:13 pm |
|
|
TINCANBANDIT
Site Supporter
Location: Mohave Valley Arizona Joined: Fri May 20, 2011 Posts: 13371
Real Name: Casey
|
sportsdad60 wrote: I really don't want to sand smooth anything, I want to keep the dings and what not in the stock. Each one probably has a story to tell, so maybe I'll just remove the varnish as suggested above, wipe it down with acetone, then begin the "linseed oil" slurry with 000 steel wool or 1200 grit OK, I guess I misunderstood the use of the word "original"
_________________Actor portrayal, Action figures sold separately, You must be at least this tall to ride, Individual results may vary, Sales tax not included, All models are over 18 years of age, upon approval of credit, Quantities are limited while supplies last, Some restrictions apply, Not available with other offers, At participating locations only, Void where prohibited, Above terms subject to change without notice, Patent pending.See my blog: http://tincanbandit.blogspot.com/
|
Thu Oct 19, 2017 1:17 pm |
|
|
Redcoat3340
Location: Bothell & New York Joined: Fri Oct 25, 2013 Posts: 448
|
Before you do anything else....go here http://www.surplusrifleforum.com/viewfo ... e536236cfband read everything you can by Candyman. I did four Enfields, three Mosins, two Swedes, a Krag, and a couple of Turk Mausers....and while it takes a bit of work...the results are the best I've found anywhere. You'll leave every ding and dent as it was...but all the old goop will be gone and you'll have a almost original BLO (Boiled Linseed Oil) finish. Then use some "Toms" gun wax and you'll be envy of the firing line.
|
Sat Oct 21, 2017 8:34 pm |
|
|
sportsdad60
Site Supporter
Location: The banana belt of MT Joined: Wed Dec 30, 2015 Posts: 8587
Real Name: Brian
|
Here is another problem stock that I want to finish but AFTER it's been repaired.... Any recommendations of local professional stock repairs?
I have a 1913 Savage 99 stock with a ‘perch’ bellie that needs repair. I also have a late model stock with similar grain that can be used to repair the 1913 stock. I don't want to do this myself as I don't have the proper woodworking tools nor do I want to buy them as I'm downsizing to move.
See attached.
*Disregard request, found a gentlman in Tri Cities that does stock repair. Brian
You do not have the required permissions to view the files attached to this post.
_________________ "I hate to advocate drugs, alcohol, violence, or insanity to anyone, but they've always worked for me."- Hunter S. Thompson
|
Mon Oct 23, 2017 10:09 am |
|
|
|
|
Page 1 of 1
|
[ 9 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 24 guests |
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
|
|