WaGuns.org
https://www.waguns.org/

Armory Craft Flat P22X Triggers
https://www.waguns.org/viewtopic.php?f=35&t=80012		 Page 1 of 1
Author:  Ops [ Mon Apr 03, 2017 5:14 pm ]
Post subject:  Armory Craft Flat P22X Triggers
Company out of Florida has made flat triggers for Sig P22X pistols DA/SA - https://www.armorycraft.com/

the instructions aren't the best

So I have figured out the best way to get this to work.

after the original trigger is removed , put the AC in and put the pin in only securing it. attach the trigger bar spring and pull the trigger.

On my 227 it would not do DA until I filed almost all the delrin pin down. Each pistol is going to be different.

once I could do DA/SA without any issues I was able to drop the locking block in with no issues.

then its just figuring out the reset point.

Image

Image

I am going to be swapping out most of my triggers to these. very nice fit and trigger pull. the first ones always the hardest
Author:  usrifle [ Mon Apr 03, 2017 5:19 pm ]
Post subject:  Re: Armory Craft Flat P22X Triggers
Why is yours canted so far forward? The SIG on the website pic doesn't look so canted.
Author:  Ops [ Mon Apr 03, 2017 5:23 pm ]
Post subject:  Re: Armory Craft Flat P22X Triggers
it depends on how much of the delrin pin has to be removed. since fit and finish is different on each pistol

also if you look at the pictures you'll see in da mode it sticks forward
Author:  usrifle [ Mon Apr 03, 2017 5:26 pm ]
Post subject:  Re: Armory Craft Flat P22X Triggers
You would think SIG would be more consistent. So they manufacture these triggers with extra pin material to be filed off on install?
Author:  Ops [ Mon Apr 03, 2017 5:32 pm ]
Post subject:  Re: Armory Craft Flat P22X Triggers
yeap a delrin pin you can easily file down. sure has a nice feel to it
Author:  lunacite [ Mon Apr 03, 2017 10:13 pm ]
Post subject:  Re: Armory Craft Flat P22X Triggers
How does the trigger pull distance compare to to the standard trigger & short trigger?
Author:  usrifle [ Mon Apr 03, 2017 10:15 pm ]
Post subject:  Re: Armory Craft Flat P22X Triggers
lunacite wrote:
How does the trigger pull distance compare to to the standard trigger & short trigger?


Sure makes it look like a long reach, doesn't it?
Author:  Ops [ Tue Apr 04, 2017 7:20 am ]
Post subject:  Re: Armory Craft Flat P22X Triggers
it actually feels shorter and so is the reset. very clean.

you can remove all pre travel, and adjust the reset to under a mm
Author:  Ops [ Tue Apr 04, 2017 12:19 pm ]
Post subject:  Re: Armory Craft Flat P22X Triggers
Image

Image

Image
Author:  mislabeled [ Tue Apr 04, 2017 4:51 pm ]
Post subject:  Re: Armory Craft Flat P22X Triggers
I know the thin triggers are shit (already swapped one of them out), but what's the advantage of this over a fat trigger? Is it just personal preference?
Author:  Ops [ Tue Apr 04, 2017 4:56 pm ]
Post subject:  Re: Armory Craft Flat P22X Triggers
it gives you a better pull and is consistent. my finger sits in the same spot every time. plus your finger feels like it belongs on the trigger.
Author:  Unicorn [ Tue Apr 04, 2017 9:30 pm ]
Post subject:  Re: Armory Craft Flat P22X Triggers
Great... something else to spend money on! The fact that it works with the SRT is a definite selling point.
Author:  das_napeth [ Wed Apr 05, 2017 7:29 pm ]
Post subject:  Re: Armory Craft Flat P22X Triggers
Ill keep my Legion triggers...thanks
Author:  Ops [ Wed Apr 05, 2017 9:21 pm ]
Post subject:  Re: Armory Craft Flat P22X Triggers
das_napeth wrote:
Ill keep my Legion triggers...thanks


I put one in my legion and it makes it even better, no pre travel and shorter reset
Author:  das_napeth [ Thu Apr 06, 2017 7:21 am ]
Post subject:  Re: Armory Craft Flat P22X Triggers
Ops wrote:
das_napeth wrote:
Ill keep my Legion triggers...thanks


I put one in my legion and it makes it even better, no pre travel and shorter reset


Pretty hard to believe but damn sweet if it really does!
Page 1 of 1 All times are UTC - 8 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/